The short answer
- An automatic press needs more air than most shop compressors deliver — the commonest unbudgeted cost
- Dryers and automatics frequently need three-phase power; confirm with an electrician, not a spec sheet
- Extraction is required for washout chemistry and for curing fumes
- Washout needs drainage with a filtration trap, which is often a legal requirement
- Check services before you sign, not after the machine arrives
Equipment purchases are costed on the machine and derailed by the services it needs. A press that cannot be run because the compressor is too small, a dryer waiting on an electrician, a washout booth with nowhere legal to drain — each of these is a machine sitting idle with a finance payment running.
None of it is expensive to check in advance and all of it is expensive to discover late.
Why this stops deliveries
Because the services conversation happens with a different person than the sales conversation. The dealer sells the machine; the electrician, the plumber and the compressor supplier are your problem, and they have their own lead times.
The pattern is consistent: machine ordered, delivered, uncrated, and then a two to four week wait for a supply upgrade or a larger compressor that nobody scoped. Meanwhile the work the machine was bought for is still being produced the old way.
The lead time on an electrician is longer than the lead time on most presses.
Compressed air
The single most common unbudgeted item. A pneumatic automatic press needs a sustained air supply, and the compressor running your existing shop almost certainly cannot provide it — it was sized for a staple gun and a blow-off nozzle.
What matters is not tank size but sustained delivery. A press cycling continuously draws air constantly, and a compressor that cannot keep up runs permanently, overheats, and delivers falling pressure that shows up as inconsistent print.
Ask the dealer, in writing
- Air consumption at full production, not peak demand
- Minimum working pressure required
- Whether the air must be dried and filtered, and to what standard
- Recommended compressor specification for this machine
- What happens to print quality if pressure drops
Air drying is the part people skip. Moisture in the line reaches pneumatic components and, worse, can reach the garment. A dryer and filter on the line is a small cost against replacing valves and cylinders.
Site the compressor away from the press. They are loud, they generate heat, and a compressor beside a work area makes the shop unpleasant — which is a layout decision best made before it is installed rather than after.
Electrical supply
Conveyor dryers and automatic presses are the heavy loads, and both frequently need more than a standard single-phase supply. A dryer in particular draws substantial current continuously rather than in bursts.
| Equipment | Typically needs |
|---|---|
| Conveyor dryer | Dedicated high-current circuit, often three-phase |
| Automatic press | Frequently three-phase |
| Compressor | Dedicated circuit; three-phase if large |
| Heat press | Dedicated circuit — do not share |
| Digital printer | Clean, stable supply; often a conditioner |
| Exposure — metal halide | High draw during exposure |
Get an electrician to look at your board before ordering, not after delivery. Two questions decide most of it: does the building have three-phase available, and does the board have capacity for another dedicated circuit? If the answer to either is no, that is a cost and a lead time belonging in the purchase decision.
The digital printer row is easy to overlook. Inkjet equipment is sensitive to supply quality as well as quantity, and a shop where the lights dim when the dryer cycles is a shop where a printhead will eventually be damaged.
Extraction and ventilation
Two separate needs. Chemical extraction at the washout area, because stripper and haze remover produce fumes that must not accumulate. Heat and fume extraction at the dryer, because curing ink releases fumes and a dryer heats the space around it.
Both are usually regulatory as well as practical. Requirements vary by jurisdiction, and the time to establish them is before installation, when ducting can be routed sensibly rather than retrofitted around finished equipment.
A shop that is uncomfortably hot in summer is usually a shop with inadequate dryer extraction, and that affects more than comfort — it affects the temperature stability that digital equipment specifies, and it makes the wash-testing you do in one season unrepresentative of another.
Water and drainage
Screen washout needs a water supply at pressure and a drain, and the drain is the part with rules attached. Emulsion, ink and reclaim chemistry must not enter the wastewater system untreated, and a filtration trap is normally required.
What the washout area needs
- Water at usable pressure, ideally from a pressure washer
- A drain with a filtration trap, serviced on a schedule
- Containment so overspray does not reach the rest of the floor
- A written disposal route for filtered waste
- An eyewash station within reach
- Confirmation of local discharge requirements
Traps block, and a blocked trap becomes urgent immediately because reclaim stops. It belongs on the monthly maintenance list rather than being attended to when it fails.
Checking before you buy
Before signing for any machine
- Full electrical specification — phase, voltage, current — confirmed by an electrician
- Air requirement at production, and whether your compressor meets it
- Extraction requirement and whether it can be routed
- Water and drainage, including any trap
- Floor loading, doorway widths and ceiling height
- Working clearance around the machine for operation and service
- Environmental range — temperature and humidity
Ask the dealer how the machine was installed at a comparable site and what it took. A machine that entered a unit before a wall went up is a machine that may not enter yours the same way, and rigging is its own cost.
All of this belongs in the fixed-cost side of the arithmetic when you work out whether the machine pays. Rigging, an electrician, a larger compressor and extraction can add meaningfully to a purchase price, and leaving them out produces a cost per print that was never achievable. The rest of the equipment archive assumes you checked the building before you bought the machine.



