EquipmentPublished

Conveyor dryers: sizing, settings and the bottleneck nobody plans for

The dryer decides your throughput and your wash test. Belt width, chamber length, and why a faster press does not make a faster shop.

  • 12 min read
  • 1,087 words
Conveyor dryers: sizing, settings and the bottleneck nobody plans for — equipment machine at a print shop
Equipment12 min readA1printsoft EditorialPhoto: Cemrecan Yurtman / Unsplash
On this page7 sections

The short answer

  • The dryer, not the press, is the real throughput limit in most shops
  • Size it on the process you run — water-based needs roughly three times the dwell of plastisol
  • Measure temperature at the belt, across its width; the panel is not evidence
  • A dryer cooler at one edge undercures everything down that side, invisibly
  • Electrical supply and extraction are what delay installation, not the machine

A conveyor dryer is the least discussed machine in a decorating shop and the one that quietly sets its ceiling. Shops upgrade presses, add heads, buy faster digital equipment, and then find output has barely moved — because everything still has to pass through the same tunnel at the same speed.

Why the dryer is the constraint

Because it is the only machine every garment must pass through, and its speed is fixed by chemistry rather than by effort. A press can be run harder; a dryer cannot cure faster than the ink allows.

That makes it the true measure of capacity. If your dryer processes 300 garments an hour, your shop produces 300 garments an hour regardless of what the press is rated at — which is why a schedule built on press speed will be wrong every week.

It is also the machine that decides whether work survives. A press fault is visible immediately; a dryer running cool produces prints that look perfect and fail at the customer, which is the most expensive kind of failure available.

Your shop's capacity is whatever your dryer can cure. Everything else is upstream of it.

Sizing one

Three dimensions matter, and the important one is not the one people ask about.

DimensionDetermines
Belt widthHow many garments across, and maximum print width
Heated chamber lengthDwell time at a given belt speed — the real capacity figure
Heat outputWhether it reaches temperature at speed

Chamber length is the number to compare. A long chamber can run a fast belt and still give adequate dwell; a short one has to crawl. Two dryers with the same belt width and wildly different chambers are not comparable machines.

Size for the process you actually run. If you print water-based ink, which must evaporate water before cross-linking and wants around three minutes against plastisol's one, a dryer sized for plastisol throughput will constrain you to a third of it.

Belt speed and dwell

Dwell is the time a garment spends in the heated chamber, and it is chamber length divided by belt speed. That is the only relationship that matters, and it is worth calculating rather than adjusting by feel.

Establishing settings for a new combination

  • Set temperature per the ink manufacturer, not by habit
  • Run one garment and check cure — stretch test first
  • Adjust belt speed before temperature; time is the safer variable
  • Wash test at five cycles before committing a run
  • Record the setting against that garment and ink
  • Re-test when the garment weight changes

Adjusting speed rather than temperature is the habit worth forming. There is a ceiling on heat — too hot and you scorch the garment or gloss the ink — but adding dwell is almost always safe, at the cost of throughput.

The garment weight point catches shops with mixed orders. A dryer set correctly for tees will frequently undercure hoodies in the same run, because the heavier garment absorbs heat that should have gone into the ink. Mixed-weight orders need either two passes or a slower belt.

Measuring temperature properly

The panel reading is a setpoint, not a measurement. What matters is the temperature the ink film reaches, and the only way to know is to measure at the belt.

The weekly check

  • Use an infrared thermometer or heat strips, not the display
  • Measure at the centre and both edges of the belt
  • Measure at the same points every time so drift is visible
  • Record it, with the date and the belt speed
  • Investigate any edge more than a few degrees below centre

Edge variation is the fault that produces the strangest complaints. A dryer cooler at one edge undercures everything that passes down that side, so a run comes back with roughly half the garments failing — which looks like a random quality problem and is a measurable machine fault.

Common faults

SymptomUsually
Prints failing on one side of the runAn element down or an edge running cool
Gradual undercure over monthsElements ageing; recalibrate
Belt tracking off to one sideTension or roller alignment
Scorching on light garmentsToo hot, compensating for short dwell
Smoke or strong fumesExtraction inadequate or blocked
Shop uncomfortably hotExtraction, again

The gradual case is the dangerous one because nothing announces it. Elements lose output as they age, so a dryer proved at installation drifts over a year or two into undercuring — which is why the temperature check belongs on the weekly list rather than being done once.

Services

The dryer is the heaviest electrical load in most decorating shops and frequently needs a dedicated high-current circuit, often three-phase. It also needs extraction, both for fumes and because it heats the space around it.

Get an electrician to confirm the supply before ordering. A dryer waiting on a board upgrade is the most common cause of new equipment sitting uncrated, and it is entirely avoidable — the same services check that applies to any machine.

Site it with catch space at the exit. Garments emerging with nowhere to go get stacked while still warm, which marks prints that were produced correctly.

Buying decisions

If youThen
Run plastisol, moderate volumeA modest chamber is adequate
Run water-basedSize for three times the dwell
Are upgrading to an automatic pressThe dryer must be upgraded with it
Cure DTF or transfersCheck the press, not just the dryer
Are buying usedMeasure every element individually

The third row is the one shops discover expensively. A press that prints six times faster feeding an unchanged dryer has simply moved the bottleneck, and the automatic sits waiting — which means the case for it should have included the dryer in the fixed costs from the start.

On a used dryer, measure output element by element rather than trusting a demonstration. Elements are the consumable part, they are not cheap in quantity, and a seller is unlikely to volunteer that half of them are near the end of their life. The rest of the equipment archive assumes the dryer sets your capacity.

Filed underEquipment
Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on equipment

All Equipment articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.