EquipmentTop 10sPublished

The DTG printers worth knowing in 2026, by tier

Entry machines start near $8,000, mid-production runs $15,000–$30,000, and industrial passes $80,000. What each tier actually buys you, and the running costs nobody quotes.

  • 15 min read
  • 1,882 words
The DTG printers worth knowing in 2026, by tier — dtg at a print shop
Equipment15 min readA1printsoft EditorialPhoto: Bank Phrom / Unsplash
On this page10 sections

The short answer

  • DTG spans roughly $8,000 entry to $500,000+ industrial; most shops buy between those extremes
  • Mid-production machines run $15,000–$30,000 — the Brother GTX Pro is cited around $19k, the older Epson F2100 around $12k
  • Kornit sits at the top: Breeze and Atlas figures start above $50,000, Atlas cited at $80,000+
  • White ink and pretreatment, not the printer, determine your cost per dark garment
  • Some current machines print DTG and DTF from one unit, which changes the buying decision

Buying a direct-to-garment printer is the point where a decorating shop commits real capital to a process. Get the tier right and the machine quietly earns for five years. Get it wrong in either direction — too small and it becomes the bottleneck, too large and the finance payment outruns the work — and it is an expensive mistake to unwind.

What follows is organised by tier rather than as a ranked list, for a reason worth stating up front.

Why this is not a top-ten ranking

Published prices for these machines are verifiable and useful, and they are quoted below with that in mind. A like-for-like ranking on speed and print quality across ten printers is a different claim, and it is not one anybody can make honestly from published material — throughput figures are quoted under different conditions, on different garments, at different resolutions, with and without white underbase.

So this covers what each tier buys, which machines sit in it, and what to verify with a dealer before signing. If you are considering a used machine instead, the risks are different again. Treat every price here as a published figure that varies by configuration, region and what is bundled — and confirm it against a written quote rather than against an article.

What are the tiers?

TierPriceSuits
Entryfrom ~$8,000Low volume, testing the market
Mid-production$15,000–$30,000Most established decorating shops
High / industrial$50,000–$500,000+Volume operations, on-demand fulfilment

The gap between entry and mid-production is where most of the disappointment lives. An $8,000 machine and a $19,000 machine both print garments, and on a single sample they can look comparable. The difference appears across a shift, in the form of maintenance time, nozzle reliability and how many garments come out consistent.

Entry: under $15,000

Entry machines exist to let a shop find out whether DTG earns its place. That is a legitimate reason to buy one, and the honest framing is that you are buying a trial rather than a production asset.

The Epson F2100, cited around $12,000, has been the reference point in this bracket for years, and the ColDesi DTG G4 is commonly listed as a beginner-oriented option. Machines below that sit in territory where you should be especially careful about who supports them and where parts come from.

What you get: genuine DTG output, on cotton, at low volume. What you do not get: throughput. If your realistic volume is more than a few dozen prints a day, an entry machine will become the constraint on everything else in the shop, and you will be buying again within two years.

An entry machine is a way of finding out whether you need a real one.

Mid-production: $15,000 to $30,000

This is where most established shops should be looking, and where the two dominant names sit.

Brother GTX Pro, cited around $19,000, has a strong following among small and mid-sized shops specifically for speed, low maintenance and its ability to sustain volume. Brother's reputation in DTG rests on the GTX line, and the maintenance story is the part owners tend to mention first.

Epson SureColor F2270 is the current mainstream Epson, built on a PrecisionCore MicroTFP printhead with UltraChrome DG2 ink. Notably it is purpose-built for both DTG and DTF from one unit, which is a meaningful change to the buying decision rather than a marketing line. Its maintenance design includes dedicated cleaning solution channels and a fabric head wiper intended to cut downtime.

Epson also fields the F3070 at the upper end of this bracket, which is where the head-to-head comparisons with the Brother GTX Pro usually happen. If you are choosing between them, that is the pairing to ask a dealer to demonstrate side by side on your own garments.

MachineCited priceNotable for
Epson F2100~$12,000Long-standing entry reference
Epson SureColor F2270Mid-productionDTG and DTF from one unit
Brother GTX Pro~$19,000Speed, low maintenance, volume
Epson SureColor F3070Upper midHigher-volume Epson platform
Kornit Breeze$50,000+Integrated pretreatment
Kornit Atlas / Atlas MAX$80,000+Industrial throughput

Industrial: $50,000 and up

Kornit is the name that defines this tier. The Breeze is cited above $50,000 and the Atlas above $80,000, with the Atlas MAX positioned as enterprise equipment. Industrial DTG as a category runs to $500,000+ at the very top.

What separates this tier is not print quality in a single-sample sense — it is throughput, consistency across thousands of garments, and integration. Kornit machines integrate pretreatment into the printer rather than requiring a separate station, and use water-based inks, which is why they come up in conversations about eco-credentials as well as volume.

The buying question at this tier is not really about the machine. It is whether you have contracted volume to fill it. A machine at this price is a commitment to a business model — usually on-demand fulfilment at scale — rather than an upgrade to an existing shop.

Why white ink is the real running cost

The purchase price gets the attention and the white ink writes the cheques. Printing on a dark garment requires a white underbase, and white ink is consumed in volume, costs more than colour, and is the component most prone to settling and clogging if the machine is not used regularly.

This is why the same printer produces wildly different economics in two shops. A shop printing mostly light cotton skips the underbase entirely and sees ink costs drop sharply. A shop printing mostly dark garments is buying white ink continuously, and that — not the finance payment — is what determines whether the machine is profitable.

Ask for ink cost per print on your work

  • Quoted on a dark garment with full white underbase, not a light one
  • At the print size you actually sell, not a small chest logo
  • Including the ink used by daily maintenance cycles, not just by prints
  • With the cost of white ink that expires unused if the machine sits idle

That last point is the one that surprises people. White ink has a shelf life and needs circulation; a machine that runs three days a week wastes more of it than one running five. If your volume is intermittent, factor that waste in — it is a real cost that no spec sheet shows.

What about pretreatment?

Pretreatment is the fluid applied to a garment before printing so the white ink sits up rather than soaking in. On most machines it is a separate step with its own equipment, its own consumable and its own labour, and it is the step most likely to be done inconsistently.

Done badly it produces the two faults every DTG shop recognises: too little and the white looks grey and blotchy; too much and there is a visible box around the print where the pretreat cured. Neither is a printer fault, and both get blamed on the printer.

Machines that integrate pretreatment — Kornit's approach — remove that variability, which is part of what the price buys. If you are staying below that tier, budget for a proper pretreat station rather than a spray bottle, and treat operator training on it as seriously as training on the printer.

Does dual DTG and DTF change things?

Yes, and it is the most consequential recent shift in this decision. A machine purpose-built for both, like the F2270, means one capital purchase covering two processes — though DTF still needs a press that holds even pressure — DTG for cotton and soft hand, DTF for polyester, blends, bags and caps.

Before dual machines, a shop wanting both bought two. Now the question is whether one unit doing both suits your mix better than two dedicated machines, and the answer depends on volume: one machine cannot run both processes simultaneously, so at higher throughput two dedicated units still win.

If you are weighing which process your work actually needs, the per-print economics are covered in the DTF and DTG cost comparison — and worth settling before choosing hardware, because the answer changes which tier you need.

What to ask the dealer

The specification sheet answers none of the questions that matter after year one.

Ten questions worth a written answer

  • What is the price with everything I need to print on day one, including pretreat?
  • What throughput should I expect on a dark garment with underbase, in my shop?
  • What is ink cost per print at my typical size, on darks?
  • How much ink does daily maintenance consume?
  • What maintenance is daily, weekly and monthly, and how long does each take?
  • What are the expected service costs in years three, four and five?
  • What is the current lead time on the parts that fail most often?
  • What happens if the machine sits unused for two weeks?
  • What is the electrical and environmental requirement — power, humidity, temperature?
  • Can you introduce me to a customer running this at my volume, not your best one?

The years three-to-five question is the one that separates a dealer who has supported these machines through their life from one who has only sold them. Year-one running costs are on every brochure; the back half of the machine's life is where the money actually goes.

The humidity question is not a technicality either. DTG is sensitive to environment, and a machine that performs in a climate-controlled showroom can behave differently in an unheated unit in February. Ask what the specified range is and measure your own space before you commit.

How do you choose your tier?

From your realistic volume and your garment mix, in that order — not from the machine you would like to own.

Your situationTier
Testing whether DTG earns a placeEntry, and treat it as a trial
Steady daily volume, mixed garmentsMid-production
Want DTG and DTF, moderate volumeMid-production dual unit
High volume of both processesTwo dedicated machines
Contracted on-demand fulfilmentIndustrial
Under ~400 prints a monthOutsource; do not buy yet

That last row deserves emphasis because it is the one nobody wants to hear. Below a few hundred prints a month the fixed costs — finance, service, space, and the white ink you throw away — do not spread across enough work to beat outsourcing. Working out where your own line sits is a twenty-minute exercise, and the method is in calculating cost per print before you buy.

Run that arithmetic before you take a demo, not after. A demonstration is designed to be persuasive and it will be; a break-even figure calculated at your real volume is the only thing in the room that is not selling you something. The rest of the equipment archive assumes you are buying on that number.

Filed underEquipmentTop 10s
Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on equipment

All Equipment articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.