ProductionHow-tosPublished

DTF or DTG: the real cost per print at each quantity

Published 2026 ranges put DTF at $3–$8 a print and DTG at $5–$15 at low volume. Where the two cross, and what changes on light garments.

  • 8 min read
  • 1,047 words
A heat press applying a transfer to a black garment
Production8 min readA1printsoft EditorialPhoto: Dwayne joe / Unsplash
On this page5 sections

The short answer

  • At low volume, DTF runs $3–$8 a print, DTG $5–$15
  • Past roughly 200 units, DTF can fall below $2 a unit
  • DTF consumables — ink, film, powder — are about $0.30–$1.50 a chest transfer
  • On light garments DTG skips white ink and pretreat, cutting 40–60% off its unit cost
  • DTF is generally the cheaper answer under 100 units; light cotton is DTG's strongest case

Most shops pick between direct-to-film and direct-to-garment once, when they buy a machine, and then route every order to whichever they own. The published 2026 numbers show why that costs money: the two processes do not sit in a fixed order of cheapness. Which one wins changes with the garment colour and the quantity, and the gap is large enough to matter on a single job.

What do the published ranges say?

Across 2026 trade guidance, DTF prints cost roughly $3 to $8 each at low volume and DTG roughly $5 to $15. Those are selling-side figures with margin in them. Stripped back to consumables, DTF's ink, film and powder come to about $0.30 to $1.50 for a standard chest transfer — the rest is labour, press time and margin.

QuantityDTFDTG
Under 50, dark garment$3 – $8$5 – $15
50, light cotton$3 – $6$2.50 – $4
200+under $2varies with coverage

The reason DTF holds its advantage at the small end is structural rather than about ink. DTF has no per-garment pretreat step and no platen change between sizes, and transfers for several different orders can be ganged onto one sheet and pressed later. On a six-piece order with mixed sizes, DTG spends real minutes that DTF simply does not spend.

Where do light garments change the answer?

This is the single biggest swing in the comparison and it is easy to miss. On a light garment DTG needs no white underbase and no pretreat, and the trade figures put the saving at 40 to 60 per cent of the unit cost. A light-colour DTG print at fifty units can land around $2.50 to $4.00.

At that point DTG is not merely competitive, it is usually the better answer — because it also wins on hand feel. DTG ink sits in the fibres rather than on them, so the print is soft in a way a customer notices when they pick the shirt up. If your work is largely light cotton, the machine that looked expensive per print on dark garments is the cheaper one for what you actually run.

The question is never which process is cheaper. It is which is cheaper for the garment in front of you.

What about the equipment behind the per-print figure?

The entry points differ enough to change a first purchase. DTG printers span roughly $1,800 to $14,000 for a machine worth owning, while DTF setups tend to start around $5,000 to $15,000 for a workflow including the shaker and cure. DTG uses less ink per print in many cases; DTF's ongoing spend is weighted toward film and powder as well as ink.

Those headline numbers are not the cost of ownership, and a quote built on them will be optimistic. The finance payment, the service contract, the floor space and — the one almost always omitted — the operator's time all belong in the figure. Working that out properly is its own exercise, covered in how to calculate cost per print before you buy, and the machines themselves are surveyed in the DTG tiers.

Which one survives the wash better?

Cost per print is only half the question. A cheaper print that fails after ten washes is a reprint, a refund and a customer who tells other people. The two processes fail differently, and knowing how changes which one you put on a garment somebody will wear weekly.

DTG's ink is bonded into the cotton fibre, so it fades in the way the garment fades. It does not crack, lift or peel, because there is no separate layer to come away. What it does do is soften and lighten gradually, which most customers read as normal wear rather than as a fault.

DTF sits on the surface as a thin film, held by adhesive. Correctly pressed it is extremely durable and often outlasts DTG on colour vibrancy. Pressed at the wrong temperature or pressure, it lifts at an edge — and that failure looks like a defect rather than like wear, because it is one.

The practical implication is that DTF's durability depends on your press being right, and DTG's depends on the garment being genuinely cotton. Both are controllable. Only one of them is controllable after the garment has left your shop, which is an argument for checking your press regularly rather than for preferring one process.

Before you commit to a process on a repeat programme

  • Press a sample, wash it ten times, and look at the edges — not the centre
  • Check platen temperature at the corners, not just the dial reading
  • On blends, confirm the fibre content on the actual garment, not the catalogue
  • For anything worn weekly, weight durability above per-print cost

How do you choose per order rather than per habit?

Four questions settle almost every job, and they take seconds once they are a habit.

Ask these before routing the job

  • What is the garment made of? Polyester and blends rule DTG out — the ink needs cotton fibre to bond into
  • Light or dark? Light cotton is where DTG's cost advantage and its hand feel both appear
  • How many? Under 100 favours DTF; past 150 of a one- or two-colour design, screen beats both
  • Will the customer handle it before buying? If so, hand feel is the deciding factor, not cents
  • Our production management carries the chosen process through to the shop floor

The last line of that table is the one shops forget. Neither digital process wins at volume against screen printing on a simple design, and the crossover is worth calculating once for your own shop rather than re-deciding per quote. The screen print cost model gives you the other half of that comparison, and the rest of the production archive assumes you know where your own line sits.

Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on production

All Production articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.