The short answer
- A design sized for adult large can run off a youth medium — the print area changes, the design does not
- Caps, bags and pockets have far smaller areas than people assume
- Seams, plackets, zips and pockets are obstacles, not surfaces
- State placement as a measurement from a fixed point, never as "left chest"
- Check the design against the smallest garment in the order, not the largest
Artwork is almost always designed on a rectangle, and garments are not rectangles. They have seams, curves, plackets and pockets, and they come in sizes where the printable area varies by a factor of two between the smallest and largest in the same order.
The mismatch produces a specific and avoidable category of failure: a design approved on screen that cannot physically be printed as approved on some of the garments ordered.
The artboard lies
A design on a white artboard has no scale, no seams and no edges. It looks equally plausible at any size, which is exactly the problem — the designer, the customer and the person approving the proof are all looking at something that does not constrain them.
The garment does constrain them. A print area is bounded by where the platen can reach, where seams interfere, and where the design would wrap around the side of the body.
This is why a proof should show the design on the garment with dimensions stated, rather than as artwork alone. It is the same principle as checking resolution against the ordered size, and it is why the print area has to be held per product rather than as a general setting — a cap, a tote and a hoodie do not share one.
Print areas by garment
Approximate adult figures, and worth confirming against your own platens and garments rather than taken as fixed.
| Placement | Typical adult area | Constrained by |
|---|---|---|
| Full front, tee | ~12 × 16in | Platen and side seams |
| Full back | ~14 × 18in | Platen, shoulder seams |
| Left chest | ~4 × 4in | Convention, not physics |
| Hoodie front | Reduced | Pocket and drawcords |
| Polo front | Small | Placket and buttons |
| Cap front | ~2 × 4in | Panels, seam, curve |
| Sleeve | ~3 × 3in | Seams both sides |
| Tote | Varies widely | Handles and seams |
Caps are the row that most often surprises customers. A logo that works beautifully on a chest is frequently unusable on a cap front, and the answer is a simplified version rather than a scaled one — which is a design decision to make before the order, not after.
The design does not shrink when the garment does. Only the space it has to sit in.
Sizes change everything
A single design across a size run from youth small to adult 3XL is being asked to work on garments of very different dimensions. The largest can take a design the smallest cannot physically hold.
| Size | Approx usable front width |
|---|---|
| Youth S | ~8in |
| Youth L | ~10in |
| Adult S | ~11in |
| Adult L | ~12in |
| Adult 3XL | ~14in |
Two approaches work. Design to the smallest garment in the run and print it at that size throughout — simplest, one screen, but the print looks small on the largest sizes. Or scale in bands — one size for youth, one for adult — which looks better and costs an extra screen and setup.
Either is fine; what is not fine is deciding by default. Say which you are doing on the quote, because the second one carries a real cost that does not shrink with quantity.
Obstacles
Things that are in the way rather than part of the surface.
Check for each of these
- Seams — a print crossing one will be uneven and may crack there
- Pockets — a hoodie pouch limits the front area considerably
- Plackets and buttons on polos and shirts
- Zips, which rule out a centred front design entirely
- Drawcords and eyelets around a hood
- Cap seams and the panel structure beneath
- Bag handles and their stitching
Zips are the clearest case and still get missed. A full-zip garment cannot take a centred front design; it takes two halves or a left-chest placement, and that is a conversation to have before the customer approves something that cannot be produced.
Placement conventions
Common conventions exist and should be stated as measurements rather than relied on as shared understanding.
| Placement | Typical rule |
|---|---|
| Full front | Centred, top edge ~3in below collar seam |
| Left chest | ~4in from centre, ~3in below collar seam |
| Full back | Centred, top edge ~3in below collar seam |
| Yoke | Just below the collar seam, small |
| Sleeve | Centred on the outer sleeve, clear of both seams |
Those measurements are conventions rather than laws, and they need adjusting by size — three inches below the collar on a youth small sits differently from the same measurement on a 3XL. What matters is that the number appears on the proof, because "left chest" is not a specification and it is the most common source of a placement dispute.
Checking before you commit
Before the proof goes out
- Check the design against the smallest garment in the order, not the largest
- Confirm every garment in the store or order has its own print area
- Look for seams, pockets, plackets and zips in the print zone
- State placement as a measurement from a fixed point
- For caps and bags, check the area before promising the design
- If sizes need different scales, say so and price it
Most of this can be enforced at the point of ordering rather than caught by a person later — a design that will not fit the ordered garment should be refused at upload, which is what per-product print areas in the design tool are for. Whatever catches it, the same principle applies as with resolution: check the artwork against the job, not against itself. The rest of the artwork archive assumes you sized the design to the smallest garment in the run.
Oversized and edge-to-edge prints
Large prints running close to the seams are popular and they narrow your options considerably. A design intended to reach the edges of the garment cannot be printed on a standard platen, because the platen has to fit inside the shirt.
Screen printing has a hard limit here: the print cannot extend past what the platen supports, so genuinely edge-to-edge work needs specialist equipment. A DTF transfer is often the practical answer for a one-off, since a heat press can reach closer to the edge than a screen setup can.
Either way, agree the real dimensions before approval. A customer who has approved a mock-up showing ink running to the hem, and receives a print stopping two inches short, has a legitimate complaint — and the record will show you promised it.



