ProductionPublished

Printing on blends and polyester without dye migration

Polyester dye moves into ink under heat. What causes it, how to prevent it, and why the failure often appears days after delivery.

  • 12 min read
  • 1,119 words
Printing on blends and polyester without dye migration — production general at a print shop
Production12 min readA1printsoft EditorialPhoto: Remy Gieling / Unsplash
On this page7 sections

The short answer

  • Polyester dye sublimates under heat and colours the ink from underneath
  • It often appears hours or days after printing, not on the press
  • Heat is the trigger — lower cure temperature is the primary defence
  • Blocker inks and low-cure systems exist and work
  • Test the actual garment; catalogue fibre content is not enough

A white print on a red performance shirt looks perfect leaving the shop and arrives pink. Nothing was done wrong on press, the cure was correct by the dryer's reading, and the garment still failed — because the problem is chemistry rather than technique.

What dye migration is

Polyester is dyed with disperse dyes that turn to gas at elevated temperature. When a garment passes through a dryer, some of that dye sublimates, moves upward into the ink film sitting on the fabric, and stays there.

The result is the garment's colour bleeding into the print. It is worst under white and light inks on strongly coloured polyester, and it is not removable — once the dye is in the ink film, the print is what it now looks like.

The print does not fail on press. It fails in the box, which is why the first you hear of it is often the customer.

Delayed onset is the cruel part. Migration continues after the garment leaves the dryer, so a print inspected at the end of the run can look correct and be discoloured by the following morning — and worse again after a hot car or a warm store room.

Which garments

GarmentRisk
100% cottonNone
Cotton-rich blend, light colourLow
50/50 blend, dark colourModerate
100% polyester, red or strong colourHigh
Performance / athletic wearHigh
Tri-blendsModerate, and variable
Sublimated garmentsVery high

Reds and oranges are the notorious offenders, followed by strong blues and purples. Black polyester is generally more stable, though not immune under a white underbase.

Sublimated garments are the highest risk of all, because the entire surface colour is disperse dye already deposited by heat. Anything that reheats it will move it, and that includes a heat press applying a transfer.

Preventing it

In order of effect

  • Lower the cure temperature — use a low-cure ink and hold the dryer down
  • Use a blocker or low-bleed white as the underbase
  • Reduce dwell time as well as peak temperature
  • Avoid unnecessary flash cures — every flash is another heat cycle
  • Keep the ink deposit as light as the design allows
  • Let garments cool fully before stacking or boxing

Temperature is the lever that matters. Dye sublimation is temperature-driven, so an ink that fully cures at a lower temperature removes the trigger rather than fighting the symptom.

Flash cycles are the overlooked contributor. A design needing two flashes puts the garment through three heat events rather than one, so a multi-colour print on polyester carries more risk than a single-colour one at the same dryer setting.

Cooling matters too. Stacking warm garments holds heat in the pile and extends the time the fabric spends hot, which is exactly the condition migration needs — so the folding table is part of the process, not the end of it.

Low-cure and blocker inks

InkWhat it does
Standard plastisol whiteCures hot; no barrier — highest risk
Low-bleed whiteContains blockers; the common choice
Low-cure whiteCures at reduced temperature
Low-cure low-bleedBoth defences; dearer
Dedicated blocker basePrinted under, for the worst cases

Low-cure inks demand accuracy. They cure at a lower temperature and they still have to reach it, so a dryer running by dial rather than by measurement can leave a print undercured — which fails in the wash instead of failing by colour.

Measure with a probe or temperature strips rather than trusting the dryer's display. That is worth doing regardless, and it is the difference between a considered low-cure process and a guess — the check belongs alongside routine wash testing.

Digital methods

DTG on polyester is limited: standard DTG pretreatment and inks are formulated for cotton, and polyester-capable systems are a separate proposition with their own constraints.

DTF is more forgiving because it applies at lower temperatures than a screen print cure and the film itself provides some barrier. It is not immune — a strong red polyester can still migrate through a DTF print pressed too hot or too long.

For garments where migration risk is high, sublimation onto white polyester or a cut-and-sew approach sidesteps the problem entirely rather than managing it, which is worth raising with a customer before quoting.

Testing

Before running a polyester job

  • Print one garment from the actual delivery, not a similar one
  • Cure it exactly as the run will be cured
  • Leave it 24 hours, warm rather than cold, then inspect
  • Compare against an unprinted garment in daylight
  • Wash it, and inspect again
  • Keep the sample with the job record

The 24-hour wait is the part shops skip and the part that matters, because migration is a delayed reaction. A print judged at the end of the shift tells you very little.

Note the outcome against the garment style so the knowledge survives the job. Recording that a particular style and colour migrated — in the system that holds your production records rather than in one printer's memory — is what stops the same discovery being made again next year by somebody else. The rest of the production archive assumes polyester was tested before the run started.

Telling the customer

Migration risk is a conversation to have at the quote, not an excuse to offer afterwards. A customer who chose a red performance shirt without being told anything reasonably expects a white print to stay white.

Raise it plainly and offer options. The garment choice is usually the cheapest fix available — the same design on a cotton-rich blend, or on a lighter colourway, removes the risk entirely and costs nothing to suggest before the blanks are ordered.

Where the garment is fixed — a sports club with a set colour, a uniform specification — say what you will do about it and what the residual risk is. Low-bleed inks and reduced cure temperatures make failure unlikely rather than impossible, and a customer told that in advance treats a slight shift as a known property of polyester rather than as a defect.

Put the outcome of your test sample in front of them if there is any doubt. A garment they can look at settles the question in a way no description does, and it is the same principle as approving a proof: the disagreements that never happen are the ones where both parties saw the same thing first.

Filed underProduction
Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on production

All Production articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.