ProductionPublished

Quality control before it ships

Every garment leaving the shop has your name on it. A checking routine that catches faults in minutes rather than at the customer.

  • 12 min read
  • 1,002 words
Quality control before it ships — quality check at a print shop
Production12 min readA1printsoft EditorialPhoto: TECNIC Bioprocess Solutions / Unsplash
On this page7 sections

The short answer

  • Check at first print, mid-run and before packing — three cheap moments
  • The first good print is the reference for the whole run; keep it visible
  • Count twice: off the dryer, and into the box
  • A quarantine shelf stops seconds shipping by accident
  • Record the cause of every reject, or you will keep producing them

The cost of finding a fault rises steeply the later it is found. In the shop it is a garment; at the customer it is a garment, a reprint, a delivery date and a conversation about whether you are reliable.

Quality control in a decorating shop is not elaborate. It is three short checks at points where finding something is still cheap.

Where faults are found

Found atCosts
First printOne garment; the run is corrected
Mid-runSome garments; the rest are saved
Before packingThe garments; the date is intact
At the customerGarments, reprint, date, reputation
After they were wornAll of that, and the account

The gap between the first row and the fourth is the entire argument. A fault caught at first print costs a shirt; the same fault caught by the customer costs the job twice over and a conversation you cannot fully win.

The three checkpoints

First print. Before running the job, print one and check it properly against the approved proof — placement measured, colours right, registration clean, coverage even. This is where the whole run is set, and thirty seconds here saves everything downstream.

Keep that first good print at the press as the reference for the run. Comparing garment fifty against garment one is far more reliable than comparing it against a memory of what it should look like.

Mid-run. Pull one every twenty or so and compare. Things drift — ink thickens, platens warm, screens clog, a squeegee edge wears — and drift is gradual enough to be invisible unless you look deliberately.

Before packing. Every garment gets looked at as it is folded. Not inspected minutely — looked at, front and back, for the obvious.

The first good print is your reference for the run. Keep it where the operator can see it.

What to look for

At first print

  • Placement measured against the proof, not judged by eye
  • Registration — colours aligned, no gaps or overlap
  • Colour against the reference or the approved sample
  • Coverage — no thin patches or pinholes
  • Correct garment: brand, style, colour, size
  • The cure test on a new garment or ink

Before packing

  • Print present, in the right place, right way up
  • No ink marks, adhesive residue or scorching
  • No garment faults — holes, stains, seam problems
  • Correct size label matching what is on the packing list
  • For named items, the spelling against the order

Spelling on named garments deserves its own attention because it is unrecoverable. A misspelled name is scrap, not a reprint, and it is the one fault a customer never forgives — check it against the order as supplied, not against what somebody typed.

Counting

Twice, at different points, by different means. Counting once is how orders ship short.

Count coming off the dryer against the job sheet, by size. Count again into the box, against the packing list. The two should agree, and where they do not you have found something while it is still fixable.

On a store order sorted by name the second count is per bag rather than per size, and each bag is checked against its order line as it is sealed. That is slower and it is the only way a two-hundred-recipient order arrives correct.

Handling seconds

Every run produces some. What matters is that they cannot accidentally ship.

The rules

  • A physical quarantine shelf that is not near finished goods
  • Anything questionable goes there immediately, not "in a minute"
  • One person decides: reprint, second, or acceptable
  • Seconds marked so they cannot re-enter stock
  • Never ship a second without telling the customer first

The last rule is worth holding to absolutely. A customer told "one has a small mark, I've taken it off the invoice" is being dealt with honestly; the same customer finding it themselves concludes you ship faulty goods and hope.

Where a run produces more seconds than your spoilage allowance, that is a signal rather than bad luck — and it should be investigated before the next job rather than absorbed.

Recording causes

Every reject gets a cause, in one word. Individually they look like accidents; grouped over a month they are a diagnosis.

Cause clusterPoints at
RegistrationAdhesive, pallet flatness, or press wear
PlacementProof specifying placement in words
CureDryer temperature or belt speed drift
Garment faultInspection on receipt being skipped
Wrong garmentStyle number missing from the job sheet
SpellingNames transcribed rather than imported

Each has a fix costing almost nothing that prevents a category rather than an instance. That is what turns a reprint rate from a number you regret into one you can move.

Making it stick

Checks get skipped when the shop is busy, which is precisely when errors are most likely. Three things keep them happening.

Make them fast. A check taking thirty seconds survives a busy week; one taking five minutes does not. Keep the list short enough to be done properly rather than long enough to be thorough and ignored.

Give them a place. A checking bench with good light, the job sheet and the approved proof to hand. Checking done wherever there is space is checking done badly.

Name who signs it off. A person, per job, who confirms it was checked. Not to allocate blame but because an unowned step is a step that quietly stops happening.

None of this is quality control in an industrial sense. It is three short looks at points where looking is cheap, and it is the difference between finding your own mistakes and having customers find them. The rest of the production archive assumes somebody looked at the garment before it was boxed.

Filed underProduction
Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on production

All Production articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.